Moto phone tools won't read my V300?

Maybe you have wrong driver installed. Reads like that.
Go to Device manager, remove the driver.

Restart MPT without the phone plugged in.
When MPT tells you to plug in the phone, then plug it in. MPT should find
the phone within a few minutes and install add drivers automatically.

A V300 should pop up on your PC screen.

If this doesn't work, it may be an incompatible data cable. The cables for
V120, V60, T720, T730 all work with the new Vseries, not sure about Nextel
cables

--
Steve
"Part86" <part86@aol.com> wrote in message
news:20040219231205.28329.00000022@mb-m29.aol.com...
> forgot to add... windows reads the phone as a new device and prompts me to
> select a driver. I click on the usb motorola driver and click ok. It says
the
> device isn't exactly compatible with the driver but I click ok anyways and
it
> completes the installation and prompts tro restart computer, which I do
and
> then when it restarts windows reads it as a new device again and I start
all
> over. When I start mobile phone tools, it says connect phone so I connect
it to
> the usb cable and windows just pops up with the new hardware window again,
but
> phone tools can't read the phone. anyone have any suggestions for me?

>Maybe you have wrong driver installed. Reads like that.
>Go to Device manager, remove the driver.
>
>Restart MPT without the phone plugged in.
>When MPT tells you to plug in the phone, then plug it in. MPT should find
>the phone within a few minutes and install add drivers automatically.
>
>A V300 should pop up on your PC screen.
>
>If this doesn't work, it may be an incompatible data cable. The cables for
>V120, V60, T720, T730 all work with the new Vseries, not sure about Nextel
>cables
>

thanks i'll try. the cable says it's compatible with all models starting in i,
so it might be the cable. If it was the wrong cable though, why would it fit
the phone and windows read it "V300"?

I also noticed that it says "make sure your phone isn't locked" when starting
moto phone tools. How do I unlock my phone? I dloaded moto service software and
it won't read the phone either. It seems windows is the only program to
acknowledge the phone, and it does as a "v300".

ok, basically i kinda had the same problem this is wat you need t
do....

load up phone tools, wait till it says it hasnt detected your phone

then take the cable out of ur fone, and plug it back in where i
prompts you to, a clock should appear, spinning like mad.... when the
disappears it will ask you to select your phone/modem, from a list
select the motorola modem option, then click next, it should run
diagnostic test to see the fones status, if it passes that then you
sorted, if not go back and try selecting the modems from the lis
(should only be 3-4), untill one setting works!


hope that helps

-
hea
-----------------------------------------------------------------------
http://cellphoneforums.netView this thread: http://cellphoneforums.net/t110132.htm

>ok, basically i kinda had the same problem this is wat you need to
>do....
>
>load up phone tools, wait till it says it hasnt detected your phone
>
>then take the cable out of ur fone, and plug it back in where it
>prompts you to, a clock should appear, spinning like mad.... when then
>disappears it will ask you to select your phone/modem, from a list,
>select the motorola modem option, then click next, it should run a
>diagnostic test to see the fones status, if it passes that then your
>sorted, if not go back and try selecting the modems from the list
>(should only be 3-4), untill one setting works!
>
>
>hope that helps!

See,... I don't get a list of phones? The clock just stops spinning and a basic
looking phone pops up, as if it has given up searching. I click setup and "add
phone" but it says "no devices read". My phone is still locked with Tmobile,
and I was guessing that was the problem. I just payed $50 for an online code to
unlock it which I haven't recieved yet. This is really frustrating! I have
concluded (maybe falsely) that the cable is not the issue because my computer
reads the phone "V300", it fits the phone, and when I plug it into the phone
when MPT promps me, the clock starts up, so it is definitely communicating with
my pc.